Arrow-right Camera
The Spokesman-Review Newspaper
Spokane, Washington  Est. May 19, 1883

Ask The Builder: Poor duct sizing may be why certain rooms in your house are cold

Main heating supply ducts need to get smaller the farther away they are from the furnace. (Tribune Content Agency)
By Tim Carter Tribune Content Agency

Q. I’ve got a forced-air furnace. Several rooms in my house are cold in the winter and are hot and stuffy in the summer when the AC is on. Most of the rooms are comfortable. Why do you think this is the case? What can be done to fix it? And if I build a new home, how can I prevent it? – Kelly S., Rochester, N.Y.

A. A lot of people have the same heating and cooling problems that Kelly has. I know that based on the number of people who email me each week when it gets cold and hot.

There are several possible reasons why a few rooms in your home might not be as comfortable as others. Let’s assume that the vent covers in the rooms are wide open, the damper controls in the branch ducts are wide open, and there are no stuffed animals being held prisoner down in the ducts.

It’s important to realize that furnaces and AC units are like shoes and clothes. They are matched to the heating and cooling requirements of your home. If you buy shoes that are too small, you’ll be uncomfortable. A professional heating and cooling contractor will do calculations that tell him exactly how many cubic feet per minute of conditioned air must go into each room to keep you comfortable.

The supply air duct system in your home needs to mimic the blood vessels in your body. The reason your blood pressure is the same throughout your entire body, even at your fingertip, is because the blood vessels get smaller and smaller the farther away they are from your heart.

Your main supply duct needs to do the same. Otherwise, there’s not enough energy in the remaining forced air to push into the rooms at the far end of your home. If your basement is unfinished, look at your main supply duct to see if it gets smaller as branch ducts go off toward the other rooms that are comfortable.

You might be able to fix your existing supply ducts with relative ease if they’re accessible. The first step in the process is to have a contractor do the calculations to see if enough air is getting to each room. There are online help aids if you want to do this yourself. Look for a Manual J guidebook if you want to try your hand at the calculations.

The second step is to make sure your furnace or AC units are indeed the correct sizes. A professional contractor will probably have to assist you with this. If your furnace and AC unit are sized properly, then make sure your main supply duct does get smaller and smaller. If it doesn’t, then you’ll have to modify it.

Q. I’m in a constant battle fighting mold, mildew and algae on my outdoor patio and sidewalks. I’m tired of scrubbing them. Is there some magic liquid I can spray on the concrete and paver brick? – David L., Orlando, Fla.

A. I have the same problem. On the north side of my home, I’ve got a paver stone pad outside a door from my garage. It constantly has slippery green algae I have to clean off. Well, I used to clean it.

Mold, mildew, algae and who-knows-what likes to grow where they can get abundant food and moisture. Shaded patios and sidewalks can be prime candidates. These organisms will grow on vertical surfaces, too, such as siding and brick.

I decided to solve the problem using technology from shipbuilders of old. Go back more than 200 years and the shipbuilders used thin copper plating on the hulls of sailing ships to prevent the growth of barnacles that would create drag and slow down the ships.

Copper is a natural, safe biocide. As with most things, you don’t want too much as it can cause problems. I’ve discovered a safe way to put copper on my pavers so it doesn’t leach into the pure water of the lake I live on here in New Hampshire.

I mix up about 1.75 pounds of blue copper sulfate crystals with a gallon of hot water. The crystals dissolve very fast as you stir them. I then put this solution in a standard hand-pump sprayer and apply a fine mist of the liquid just on the pavers and concrete.

I’m careful to make sure I don’t get any in the grass, and I only put on enough so it doesn’t puddle. You’ll discover it almost always soaks into the masonry in a few minutes.

After it dries, I apply more. I do this about three or four times so the copper soaks down into the surface of the masonry. The surface of the concrete does end up with a blueish color, but the color fades away in a week or two. The best part is I don’t have any algae, mold or mildew problems, and neither will you.

Subscribe to Carter’s free newsletter and listen to his new podcasts. Go to: www.AsktheBuilder.com.